Old Vintage World Map Wallpaper Mural

Prepare your paper

Your mural is printed on 45 cm wide strips that are helpfully numbered on each strip in the order to be hung. Finding the number on the strip, lay out in numerical order (number 1 on top).

You are now ready to install.

Remember – we have made allowances for trimming top and bottom to compensate for uneven walls.

Place the first panel

Apply your pre mixed wallpaper adhesive directly to the wall, making sure to have a gone beyond the width of the paper, to avoid pasting the face of the previous panel. Apply evenly, leaving no dry misses and paying particular attention to all corners, skirting, ceiling lines and electric points.

Always isolate any electrical points that you are working near before installation. If in any doubt consult a qualified electrical engineer who will be able to assist you.

Hang the first length, working from top to bottom, allowing the paper to fall naturally.

Working first vertically and then horizontally smooth over with a soft brush to ensure no air bubbles remain trapped underneath.

Check carefully that you have followed your plumb line for correct alignment, checking in key image areas (eye level and focal points) before trimming top and bottom.

If necessary to achieve a good alignment, carefully pull back or remove and reposition your mural and proceed as above.

Perfect your panels

For Standard, Premium & Textured Papers

To hang your custom wallpaper just hang the panels from edge to edge, butting together with no overlap.

Match the image at the join and adjust slightly until the design completely matches.

Smooth the paper with a soft brush first vertically then horizontally.

When you are completely happy with the effect you are ready to trim the excess from the top, bottom and any edges for a professional finish using a knife and straight edge.

Checking the entire length of the joint is matched and not overlapped, gently using the seam roller ensure the joins are well bonded.

Wipe away any excess paste from the face of the paper, skirting’s, ceilings and electrical points with a dry or slightly dampened clean sponge.

Repeat to complete

Continue until all panels are hung and your mural is complete using the method described above.

Carefully remove any adhesive or residue with clean warm water and a sponge.

Allow to dry thoroughly before carrying out any further works on or in close proximity to your new mural.

Step back and admire your Marmalade Art!

Prepare your paper

Your mural is printed on 45 cm wide strips that are helpfully numbered on each strip in the order to be hung. Finding the number on the strip, lay out in numerical order (number 1 on top).

You are now ready to install.

Remember – we have made allowances for trimming top and bottom to compensate for uneven walls.

Paste the wall

Apply the paste directly to the wall, allowing 10cm overlap on the width to avoid pasting the face of the wallpaper when pasting the next drop.

Take particular care to paste evenly without leaving misses especially around skirtings, corners and all edges.

Slightly dampen each piece of paper as you require and leave to soak for 10 minutes.

When the 10 minutes are nearly up. Paste the wall again then hang the first piece using a plumb line or spirit level.

Follow the instructions above. Using a soft brush or a squeeze to smooth it down, avoiding any air bubbles to ensure a perfect finish.

Always isolate any electrical points that you are working near before proceeding with installation. If in any doubt consult a qualified electrical engineer who will be able to assist you.

Hang the first length

Working from top to bottom, allowing the paper to fall naturally.

Working first vertically and then horizontally smooth over with a soft brush to ensure no air bubbles remain trapped underneath.

Check carefully that you have followed your plumb line for correct alignment, checking in key image areas (eye level and focal points) before trimming top and bottom.

If necessary to achieve a good alignment, carefully pull back or remove and reposition your mural and proceed as above

Trim away the excess paper from the top, bottom and any edges using a straight edge and a sharp knife.

Overlap the wallpaper

Overlap the edges and allow the wall mural to fall naturally and avoid it stretching.

Your paper is printed with a 20mm overlap, using the black crop marks at the top and the bottom carefully guide the paper into position at the join making sure it is completely matched.

Trim away the excess paper from the top, bottom and any edges using a straight edge and a sharp knife.

Using a sharp knife and a straight edge, pressing firmly with enough pressure to cut through both pieces, carefully cut down the centre of the overlap. The excess top strip should drop away as you cut through the join.

Remove the excess underlap

Gently peel the right hand paper back and remove the unwanted excess strip underneath the panel (see diagram).

Using more paste if required.

Use a seam roller to press the edges down and clean any excess paste from the joins with a damp clean sponge immediately.

Repeat to complete

Continue until all panels are hung and your mural is complete using the method described above.

Carefully remove any adhesive or residue with clean warm water and a sponge.

Allow to dry thoroughly before carrying out any further works on or in close proximity to your new mural.

Step back and admire your Marmalade Art!